Block Industry Start-Up Costs in Nigeria

A block industry is not bought as one item. The machine is the part that gets quoted first, and it is the part buyers understand best — but it is usually not the largest line once the yard is running. This guide breaks the investment into the blocks it is actually made of, explains what moves each one up or down, and ends with the order in which to size them. No prices are stated here: a figure that is right for one buyer's output target, block profile and power supply is wrong for the next, so the machine lines are quoted per model instead. Of the lines below, the machine and the moulds are the two RENFA builds; the rest are local costs that vary by site.

By Alex, RENFA
Last reviewed 2026-11-02 · 9 min read

What the machine price covers, and what it does not

Every machine in the range ships with one mould box. That is the mould for one block profile, and it is included because a machine without a mould cannot produce anything. Additional profiles — hollow block, paver, curb, a custom shape — are separate items ordered alongside the machine, and a yard that intends to sell more than one product should count them from the start rather than discovering the gap after the machine lands.

Quotations are written EXW, which means the price covers the machine at the factory and not the journey. Crating, inland haulage to the port, sea freight, insurance and clearance at the Nigerian end sit outside it. Buyers who compare two EXW quotations and treat the difference as the whole difference are comparing the smallest part of the bill.

The machines are driven by vibration motors. There is no hydraulic circuit in this range, which matters for budgeting: there is no hydraulic oil to change, no seals to renew and no pump to service. The wear items are the vibration motors, the mould boxes and the electricals.

Capacity, not machine size, is the sizing unit

A block machine is specified by how many blocks it produces per shift, and that number has three inputs: the moulding cycle, the number of cavities in the mould, and the hours the yard can actually run. The cycle is quoted in seconds, and small differences compound — at the same number of operating hours, a 35-second cycle produces materially more than a 45-second cycle on the same frame.

The range splits at that point. The 45-second mobile machines are the entry into production; the 35-second machines are the step up for a yard that already has demand and wants more pieces per shift. Moving up buys output, not a better machine — the build quality is the same across the line, and the honest question is how many blocks the market in front of you will absorb.

Output is also quoted per product, and the gap between products is large. The same machine that turns out standard bricks by the thousand produces hollow blocks by the hundred, because a hollow block is several times the volume of a brick. Any budget built on the brick figure and spent on hollow block moulds will be short.

Moulds: the cost that scales with your product list

One machine can carry several moulds, and each profile needs its own. This is the line that separates a yard selling one product from a yard selling four, and it is where the second-largest share of the machine-side cost usually sits.

Cavity count is the variable inside a single mould. More cavities per cycle means more blocks per cycle and a heavier, more expensive mould box, and it also asks more of the machine's drive. A six-cavity mould on a machine sized for four does not produce half again as much; it produces strain.

The practical approach is to buy the moulds for the products you can sell in the first six months and add profiles as demand appears. Moulds can be ordered after the machine is in production, so nothing is lost by staging them — provided the machine was specified with enough drive for the cavity count you intend to reach.

Power: the line most often left out of a first budget

The machines run on 380 V or 220 V, in electric and diesel versions. What has to be settled before the order is the supply the yard will actually have, because voltage and frequency are agreed at the order stage and a machine specified for one supply cannot simply be re-rated on arrival. Frequency is the harder constraint of the two — a 50 Hz machine on a 60 Hz supply, or the reverse, is a specification error, not an adjustment.

For a yard on mains power, the cost is not the machine but the supply: the connection capacity the machines need, the cabling and protection between the supply and the machine, and what happens when the supply drops. A yard that stops every time the grid does is not producing, so the realistic budget either includes a generator sized for the motors or accepts the lost shifts.

The diesel versions move that decision inside the machine. They cost more up front and cost more per block to run, but they remove the dependency on a connection that may not carry the load. Which is right depends on the site, not on the machine — which is why this is a question for the quotation stage rather than an afterthought.

Site works: the part the machine supplier never quotes

A block machine needs a level, load-bearing surface, because a vibrating machine on soft ground walks, settles and produces blocks of uneven height. That slab, the hardstanding for the curing area, and the water supply for curing are all local works and none of them travel with the machine.

The curing area is easy to under-size. Blocks have to stand while they gain strength, so the area needed is set by daily output multiplied by curing days, not by the footprint of the machine. A yard that produces more than its curing area can hold has to stop producing, which turns a capacity purchase into an idle one.

Access matters too. The machine arrives crated and has to be moved from the delivery point to the slab, and the raw materials — cement, sand, aggregate — arrive continuously afterwards. A site that cannot take a truck to the slab adds a handling cost to every tonne that comes in.

Installation and commissioning

Installation is the step where the machine stops being a delivery and starts being a production line: setting it on the slab, levelling it, connecting the supply, fitting the mould, and running the first blocks to check height and density. It is also the step most often compressed into a single day when it should not be.

What can be done locally and what needs the supplier should be settled before the machine ships rather than after. Foundation and supply connection are local work; the machine settings, mould fitting and the first production run are where a supplier's involvement pays for itself, because a machine that is correctly set from the first day does not spend its first month producing rejects.

Commissioning is also when the operating routine should be written down — the daily checks, the greasing points, what a change in block height means. A yard that learns this by trial spends months rediscovering it.

Spares and consumables in the first year

Three things wear in normal production: the vibration motors, the mould boxes and the electricals. None of them fail immediately, and all of them fail eventually, so the honest budget carries a spares allowance from the first month rather than treating the first breakdown as an emergency purchase.

Mould boxes wear at the edges and the corners first, and the symptom is a block that is no longer crisp — a burr on the arris, a height that drifts. That is wear, not a machine fault, and knowing the difference is what stops a yard from buying a new machine when it needs a new mould.

Vibration motors are the item most worth holding as a spare, because a machine without one is stopped completely. The cost of holding one is small against the cost of a week's lost production while a replacement is sourced and shipped.

Working capital, and the gap between making blocks and being paid for them

Cement, sand, aggregate, water and labour are consumed before a single block is sold, and blocks are usually sold after curing and often on terms. That gap — materials out, cash in later — is a real cost of the business and it scales with output, not with the machine.

It is also the line that catches yards that scaled too early. A larger machine consumes materials faster, which means the working capital requirement grows at the same rate as the output. A yard that buys capacity it cannot feed does not run short of blocks; it runs short of cement.

Sizing this correctly means starting from the materials cost per block at your own mix and your own local prices, then multiplying by the output you intend to run — not by the output the machine is capable of.

The order to size the numbers in

Built in the wrong order, a budget for a block yard is a list of quotations that do not fit together. Built in this order, each decision constrains the next and the total arrives at the end rather than being discovered then.

First, the output the market in front of you will absorb — blocks per day you can actually sell, not blocks per day a machine can make. Second, the machine whose cycle and cavity count reach that output. Third, the moulds for the products you will sell in the first six months. Fourth, the supply: mains capacity, or diesel, or both. Fifth, the site works — slab, curing area, access, water. Sixth, installation and commissioning. Seventh, the spares allowance. Eighth, the working capital to run at that output until the first sales are collected.

Only the second and third of those are machine lines. The rest is what a yard actually costs, and it is why two buyers who choose the same machine can end up with very different totals.

What to send for a quotation that fits

A quotation is only as good as the inputs. Sending the five items below produces a number that can be compared with another supplier's; sending a model number alone produces a price for a machine that may not be the right one.

State the blocks per day you intend to run and the profiles you intend to sell. State the power available at the site — voltage, frequency and whether it is mains, generator or both. State the port and the inland destination. State whether the yard is new or already producing. Then the quotation can be written against your situation rather than against a catalogue page.

Common questions

Does a block making machine come with a mould?

Yes — one mould box is included with every machine, for one block profile. Additional profiles such as hollow block, paver or a custom shape are separate items quoted alongside the machine, and they can be ordered later if the product list grows.

Which costs are outside an EXW machine quotation?

Crating, inland haulage to the port, sea freight, insurance and clearance at the Nigerian end are all outside an EXW price. The site works — slab, curing area, water and access — and the electrical connection to the machine are local costs that no machine quotation covers.

Is a diesel block machine cheaper to run than an electric one?

No. A diesel machine costs more to buy and more per block to run, because fuel is dearer per unit of work than grid power. It is chosen where the mains supply cannot carry the motors or cannot be relied on, which makes it a decision about the site rather than about running cost.

Can moulds be added after the machine is running?

Yes. Moulds can be ordered once demand for a second or third product appears, so there is no need to buy every profile at the start — provided the machine was specified with enough drive for the cavity count you intend to reach.

Why is there no price list on the cost guide?

Because a single figure would be wrong for most buyers. The total depends on the machine, the number and cavity count of the moulds, the power supply, the site works and the working capital the yard will run on. Machines are quoted against your own specification, and the rest is sized against your own output target.

Talk to us about this

Send the specification you have arrived at and we will confirm which model of ours matches it, with the price and the packing weight.

More buying guides

Preparing a Site for a Block Machine

What to have ready before a block machine arrives: the surface it stands on, delivery access, the power connection, mix storage and curing space.

4 min read

How to Compare Two Block Machine Quotations

Two quotations that look different usually are not. What to put on the same basis — price terms, moulds, voltage, spares and installation — before you decide.

4 min read

How to Choose a Block Making Machine

Cycle time, drive power, mould configuration and power supply — the four decisions that set the output and cost of a block making machine before you order.

6 min read

Get a specification confirmed, not a brochure

Send the requirement you have worked out — capacity, power supply, bar size or slab area — and we will confirm the model, the price and the packed weight.

WhatsApp / WeChat+86 189 0384 2606
ResponseQuotations sent within one working day