Block Making Machines in Kenya: Supply, Power and Delivery

A block machine bought for a Kenyan yard is two things at once: a machine built in China, and a service that has to exist on the ground after it lands. This guide covers both — what can be seen in Nairobi before an order is placed, what the local installation and after-sales actually cover, and the specification that decides whether the machine runs when it arrives.

By Alex, RENFA
Last reviewed 2026-10-19 · 4 min read

What is in Kenya, and what is not

Demonstration machines are kept at our Nairobi warehouse. They can be inspected before an order is placed, so the frame, the mould box, the control panel and the moulding cycle are seen in person rather than read off a specification sheet.

What is not in Kenya is sale stock. The machine you buy is built and shipped from China. That distinction is worth stating plainly because it sets expectations on both sides: the Nairobi visit does not shorten the lead time, it removes the risk of ordering from a photograph.

Why seeing the machine first matters more than the specification sheet

Two machines can carry the same cycle time and the same motor rating and still differ in ways that matter at the yard: how the mould box is clamped, how much clearance there is around the vibrator, whether the pallet feed suits the pallets you can actually buy locally, and how the control panel is labelled for an operator who has not run the machine before.

None of that is visible in a quotation. It is the part buyers usually discover after the container is cleared, when changing it is expensive.

For a first machine the visit is also where the mould decision gets settled, because the block profile you intend to sell determines the mould, and the mould determines what the machine has to be ordered with.

The specification that decides whether the machine runs

Power supply is the most common reason a machine arrives and does not work as expected. Sites differ: some have a three-phase connection and some do not. The machine has to be ordered for the supply that exists at the yard, not for the supply that could be installed later.

Two things must be confirmed before the order: the voltage and the frequency. The frequency is the one that cannot be corrected afterwards — a motor wound for 60 Hz runs at the wrong speed on a 50 Hz supply, and no adjustment at the yard fixes it. Voltage is settled by choosing the right motor option at build.

If the site has no reliable grid, the diesel-driven models remove the dependency entirely. That is a different trade rather than a better one: lower output per shift, in exchange for being able to work anywhere.

Mobile or stationary, decided by how the yard works

A mobile machine carries its own wheels and is taken to the material. A stationary machine stays in one position and is fed a higher volume. The question is not which is better but where the blocks are made.

A yard producing in one place at volume is a stationary machine with a charging hopper. A contractor moving between sites, or a yard producing in more than one location, is a mobile machine. The range covers both, from 3,600 standard bricks per shift on the smallest mobile model to 20,000 on the hopper-fed stationary versions.

The mould decides what you can sell

Every machine is quoted with one mould, and the mould is what sets the product: standard brick, hollow block for walling, or interlocking paver. Additional moulds can be ordered with the machine or later.

Choose the profile by what sells in your area rather than by what the machine can theoretically produce. A yard that cannot sell pavers has bought a mould it will not use, and that cost sits inside the delivered price of the machine.

Delivery, clearance and what the lead time is made of

Container freight for Kenya lands at Mombasa, and inland transport to Nairobi is a separate leg. Freight, clearance and inland delivery are quoted per destination rather than as one regional rate, because a machine landed in Nairobi and the same machine landed further inland are different costs.

A quoted lead time contains four things: build, crating, sailing and clearance. It is not one fixed number across models, which is why it is quoted with the order rather than printed here as a general figure.

What local after-sales covers

Installation and after-sales are handled in Kenya. In practice that means the machine is commissioned on site rather than handed over as a crate, and that a problem is answered by someone who can travel to the yard.

It does not mean every spare is held locally. The parts that wear — cutters, mould wear parts, bearings — should be discussed at the time of order, so that the first replacement is planned rather than discovered. Delivery covers the neighbouring East African markets as well.

What to send with an enquiry

Four details are enough to come back with a configuration and a delivered cost rather than a brochure:

  • The block profile and size you intend to sell, and whether more than one is needed.
  • The power available at the site: single or three phase, voltage and frequency.
  • Where the yard is, and whether blocks are made in one place or in several.
  • The output you need per shift, and the working hours you can actually run.

Common questions

Can a block machine be inspected in Kenya before buying?

Yes. Demonstration machines are kept at the Nairobi warehouse and can be inspected before an order is placed. They are demonstrators rather than sale stock — the machine you buy is built and shipped from China — so the visit removes the uncertainty of ordering from a photograph without shortening the lead time.

What power supply does a block machine need in Kenya?

It depends on the site, which is why the supply has to be stated at order. Three-phase and single-phase connections both exist, and the motor option is chosen to match. Frequency is the critical figure: a motor wound for 60 Hz runs at the wrong speed on a 50 Hz supply and cannot be corrected at the yard afterwards.

How long does delivery to Kenya take?

There is no single figure, because the lead time is made of build, crating, sailing and clearance, and the sailing leg varies. It is quoted with the order for the specific model and destination rather than stated as a general number.

Is installation included in Kenya?

Installation and after-sales are handled in Kenya, so the machine is commissioned on site rather than handed over as a crate. Wearing parts are not all held locally, so the first set of cutters or mould wear parts is best planned at the time of order.

Talk to us about this

Send the specification you have arrived at and we will confirm which model of ours matches it, with the price and the packing weight.

More buying guides

Preparing a Site for a Block Machine

What to have ready before a block machine arrives: the surface it stands on, delivery access, the power connection, mix storage and curing space.

4 min read

How to Compare Two Block Machine Quotations

Two quotations that look different usually are not. What to put on the same basis — price terms, moulds, voltage, spares and installation — before you decide.

4 min read

How to Choose a Block Making Machine

Cycle time, drive power, mould configuration and power supply — the four decisions that set the output and cost of a block making machine before you order.

6 min read

Get a specification confirmed, not a brochure

Send the requirement you have worked out — capacity, power supply, bar size or slab area — and we will confirm the model, the price and the packed weight.

WhatsApp / WeChat+86 189 0384 2606
ResponseQuotations sent within one working day